Short answer: pick the pneumatic torque wrench whose working torque range covers your target bolt torque with room to spare. Soartec models cover 320–2,100 Nm (T21) up to 950–5,800 Nm (T58). For bolts up to about 2,800 Nm, a 1" drive model (T21 or T28) is lighter and faster. Above that, choose a 1-1/2" drive model (T39, T46 or T58).
What is a pneumatic torque wrench?
A pneumatic torque wrench (also called an air torque multiplier) uses an air motor and a reduction gearbox to turn a bolt slowly and continuously to a preset torque. Unlike an air impact wrench, it does not hammer, so it delivers controlled, repeatable torque. Soartec pneumatic torque wrenches are rated for ±5% preset torque output and repeat accuracy.
Soartec pneumatic torque wrench size chart
| Model | Square drive | Working torque (Nm) | Approx. ft-lb | Free speed | Weight |
|---|---|---|---|---|---|
| T21 | 1" | 320–2,100 | 236–1,549 | 14 rpm | 7.6 kg |
| T28 | 1" | 430–2,800 | 317–2,065 | 10.5 rpm | 7.7 kg |
| T39 | 1-1/2" | 610–3,900 | 450–2,877 | 7.5 rpm | 10.3 kg |
| T46 | 1-1/2" | 750–4,600 | 553–3,393 | 7 rpm | 11.4 kg |
| T58 | 1-1/2" | 950–5,800 | 701–4,278 | 5 rpm | 14.1 kg |
All models run at 100 psi. ft-lb values are converted from Nm (1 ft-lb ≈ 1.356 Nm) and rounded.
How do I choose the right torque range?
- Find the specified bolt torque from the equipment manual or the bolting procedure.
- Choose a model whose range covers it with margin. Avoid running a tool at the very top or bottom of its range when a neighbouring model puts your target nearer the middle.
- Check breakaway torque. Loosening a corroded bolt can take more torque than tightening it, so size up if you also use the tool for disassembly.
- Match the square drive to your impact-rated sockets: 1" for T21/T28, 1-1/2" for T39/T46/T58.
- Consider speed and weight. Higher-torque models turn more slowly (14 rpm on the T21 vs 5 rpm on the T58) and weigh more (7.6 kg vs 14.1 kg).
Pneumatic torque wrench vs air impact wrench: which is better for flange bolts?
Use a pneumatic torque wrench when the bolt must reach a specified torque, such as flanges, wind-turbine and structural connections, and heavy-equipment assemblies. Use an air impact wrench for fast run-down and removal where precise final torque is not required. Many crews run nuts down with an impact wrench, then final-tighten with a torque wrench.
What comes in the kit?
Each Soartec pneumatic torque wrench set includes the torque wrench, an FRL unit (filter, regulator, lubricator), an air regulator, an air hose and a quick coupling, so you can set the air pressure that corresponds to your target torque.
FAQ
Is a pneumatic torque wrench the same as a torque multiplier?
A pneumatic torque wrench is a powered torque multiplier: the air motor drives the gearbox instead of a hand handle, which speeds up repetitive heavy bolting.
How accurate is a pneumatic torque wrench?
Soartec models are rated at ±5% for both preset torque output and repeatability.
Do I need a reaction arm?
Yes. A pneumatic torque wrench must react against a fixed point, such as an adjacent nut or a solid part of the structure, to hold the tool while it tightens.
Need help sizing a tool? Browse Soartec pneumatic torque wrenches or contact us with your bolt size and target torque for a recommendation.
